Building for Supported Renesas Boards

AGL supports building for several automotive Renesas board kits. Renesas is the number one supplier of vehicle control microcontrollers and System on a Chip (SoC) products for the automotive industry.

This section provides the build and deploy steps you need to create an image for the following Renesas platforms:

NOTE: You can find similar information for the Pro and Premier board kits on the R-Car/Boards/Yocto-Gen3 page. The information on this page describes setup and build procedures for both these Renesas development kits.

1. Downloading Proprietary Drivers

Before setting up the build environment, you need to download proprietary drivers from the R-Car H3/M3 Software library and Technical document site.

Follow these steps to download the drivers you need:

  1. Determine the Files You Need:

    Run the setup_mm_packages.sh script as follows to display the list of ZIP files containing the drivers you need. Following is an example:

    grep -rn ZIP_.= $AGL_TOP/meta-agl/meta-agl-bsp/meta-rcar-gen3/scripts/setup_mm_packages.sh

    The script's output identifies the files you need to download from the page.

  2. Get Your Board Support Package (BSP) Version:

Be sure to have the correct BSP version of the R-Car Starter Kit based on the version of the AGL software you are using. Find the appropriate download links on the R-Car H3/M3 Software library and Technical document site. The file pairs are grouped according to the Yocto Project version you are using with the AGL software. Use the following table to map the Renesas version to your AGL software:

AGL Version Renesas version
AGL master 4.1.0
  1. Download the Files:

Start the download process by clicking the download link. If you do not have an account with Renesas, you will be asked to register a free account. You must register and follow the "Click Through" licensing process in order to download these proprietary files.

If needed, follow the instructions to create the free account by providing the required account information. Once the account is registered and you are logged in, you can download the files.

NOTE: You might have to re-access the original page that contains the download links you need after creating the account and logging in.

  1. Create an Environment Variable to Point to Your Download Area:

Create and export an environment variable named XDG_DOWNLOAD_DIR that points to your download directory. Here is an example:

$ export XDG_DOWNLOAD_DIR=$HOME/Downloads
  1. Be Sure the Files Have Rights:

Be sure you have the necessary rights for the files you downloaded. You can use the following command:

chmod a+x $XDG_DOWNLOAD_DIR/*.zip
  1. Check to be Sure the Files are Downloaded and Have the Correct Rights:

Do a quick listing of the files to ensure they are in the download directory and they have the correct access rights. Here is an example:

$ ls -l $XDG_DOWNLOAD_DIR/*.zip
-rw-rw-r-- 1 scottrif scottrif 4662080 Nov 19 14:48 /home/scottrif/Downloads/R-Car_Gen3_Series_Evaluation_Software_Package_for_Linux-weston8-20200923.zip
-rw-rw-r-- 1 scottrif scottrif 3137626 Nov 19 14:49 /home/scottrif/Downloads/R-Car_Gen3_Series_Evaluation_Software_Package_of_Linux_Drivers-weston8-20200923.zip

2. Getting More Software

  1. Get the bmaptool:

Download this tool from the bmap-tools repository. The site has pre-built packages (DEB or RPM) for the supported host operating systems.

3. Getting Your Hardware Together

Gather together this list of hardware items, which is not exhaustive. Having these items ahead of time saves you from having to try and collect hardware during development:

NOTE: The Salvator-X Board has NDA restrictions. Consequently, less documentation is available for this board both here and across the Internet.

4. Making Sure Your Build Environment is Correct

The "Initializing Your Build Environment" section presented generic information for setting up your build environment using the aglsetup.sh script. If you are building an image for a supported Renesas board, you need to take steps to make sure your build host is set up correctly.

  1. Define Your Board:

Depending on your Renesas board, define and export a MACHINE variable as follows:

Board MACHINE Setting
Starter Kit Pro/M3 MACHINE=m3ulcb
Starter Kit Pro/M3 + kingfisher support MACHINE=m3ulcb-kf
Starter Kit Pro/M3 without graphic MACHINE=m3ulcb-nogfx
Starter Kit Premier/H3 MACHINE=h3ulcb
Starter Kit Premier/H3 + kingfisher support MACHINE=h3ulcb-kf
Starter Kit Premier/H3 without graphic MACHINE=h3ulcb-nogfx
Salvator-X MACHINE=h3-salvator-x

For example, the following command defines and exports the MACHINE variable for the Starter Kit Pro/M3 Board:

$ export MACHINE=m3ulcb
  1. Run the aglsetup.sh Script:

Use the following commands to run the AGL Setup script:

$ cd $AGL_TOP
$ source meta-agl/scripts/aglsetup.sh -m $MACHINE -b build agl-devel agl-demo

NOTE: Running the aglsetup.sh script automatically places you in the working directory (i.e. $AGL_TOP/build). You can change this default behavior by adding the "-f" option to the script's command line.

In the previous command, the "-m" option sets your machine to the previously defined MACHINE variable. The "-b" option defines your Build Directory, which is the default $AGL_TOP/build. Finally, the AGL features are provided to support building the AGL Demo image for the Renesas board.

You can learn more about the AGL Features in the "Initializing Your Build Environment" section.

  1. Examine the Script's Log:

Running the aglsetup.sh script creates the setup.log file, which is in the build/conf folder. You can examine this log to see the results of the script. For example, suppose the graphics drivers were missing or could not be extracted when you ran the script.

In case of missing graphics drivers, you could notice an error message similar to the following: 
    
[snip]
--- fragment /home/working/workspace_agl_master/meta-agl/templates/machine/h3ulcb/50_setup.sh
/home/working/workspace_agl_master /home/working/workspace_agl_master/build_gen3
The graphics and multimedia acceleration packages for
the R-Car Gen3 board can be downloaded from:
https://www.renesas.com/en-us/solutions/automotive/rcar-demoboard-2.html

These 2 files from there should be store in your'/home/devel/Downloads' directory.
  R-Car_Gen3_Series_Evaluation_Software_Package_for_Linux-weston5-20190802.zip
  R-Car_Gen3_Series_Evaluation_Software_Package_of_Linux_Drivers-weston5-20190802.zip
/home/working/workspace_agl_master/build_gen3
--- fragment /home/working/workspace_agl_master/meta-agl/templates/base/99_setup_EULAconf.sh
--- end of setup script
OK
Generating setup file: /home/working/workspace_agl_master/build_gen3/agl-init-build-env ... OK
------------ aglsetup.sh: Done
[snip]

If you encounter this issue, or any other unwanted behavior, you can fix the error mentioned, remove the $AGL_TOP/build directory, and then re-launch the aglsetup.sh again.

Here is another example that indicates the driver files could not be extracted from the downloads directory: 
    
[snip]

~/workspace_agl/build/conf $ cat setup.log
--- beginning of setup script
--- fragment /home/working/workspace_agl/meta-agl/templates/base/01_setup_EULAfunc.sh
--- fragment /home/working/workspace_agl/meta-agl/templates/machine/m3ulcb/50_setup.sh
~/workspace_agl ~/workspace_agl/build
ERROR: FILES "+/home/working/Downloads/R-Car_Gen3_Series_Evaluation_Software_Package_for_Linux-weston5-20190802.zip+" NOT EXTRACTING CORRECTLY
ERROR: FILES "+/home/working/Downloads/R-Car_Gen3_Series_Evaluation_Software_Package_of_Linux_Drivers-weston5-20190802.zip+" NOT EXTRACTING CORRECTLY
The graphics and multimedia acceleration packages for
the R-Car Gen3 board BSP can be downloaded from:


These 2 files from there should be stored in your
'/home/working/Downloads' directory.
  R-Car_Gen3_Series_Evaluation_Software_Package_for_Linux-weston5-20190802.zip
  R-Car_Gen3_Series_Evaluation_Software_Package_of_Linux_Drivers-weston5-20190802.zip
ERROR: Script /home/working/workspace_agl/build/conf/setup.sh failed
[snip]

5. Checking Your Configuration

Aside from environment variables and parameters you establish through running the aglsetup.sh script, you can ensure your build's configuration is just how you want it by examining the local.conf configuration file.

You can find this configuration file in the Build Directory (e.g. "$TOP_DIR/build/conf/local.conf").

In general, the defaults along with the configuration fragments the aglsetup.sh script applies in the local.conf file are good enough. However, you can customize aspects by editing the local.conf file. See the "Customizing Your Build" section for common configurations you might want to consider.

NOTE: For detailed explanations of the configurations you can make in the local.conf file, consult the Yocto Project Documentation.

A quick way to see if you have the $MACHINE variable set correctly is to use the following command:

grep -w -e "^MACHINE =" $AGL_TOP/build/conf/local.conf

Depending on the Renesas board you are using, you should see output as follows:

  MACHINE = "h3ulcb"
or 
  MACHINE = "m3ulcb"
or 
  MACHINE = "h3-salvator-x"

If you ran the aglsetup.sh script as described in the "Making Sure Your Build Environment is Correct" section earlier, the "agl-devel", "agl-demo", "agl-netboot", "agl-appfw-smack", and "agl-localdev" AGL features will be in effect. These features provide the following:

6. Using BitBake

This section shows the bitbake command used to build the AGL image. Before running BitBake to start your build, it is good to be reminded that AGL does provide pre-built images for developers that work with supported hardware. You can find these pre-built images on the AGL Download web site.

Start the build using the bitbake command.

NOTE: An initial build can take many hours depending on your CPU and and Internet connection speeds. The build also takes approximately 100G-bytes of free disk space.

For this example, the target is "agl-demo-platform":

  bitbake agl-demo-platform

The build process puts the resulting image in the Build Directory:

<build_directory>/tmp/deploy/images/$MACHINE

7. Booting the Image Using a MicroSD Card

To boot your image on the Renesas board, you need to do three things:

  1. Update all firmware on the board.
  2. Prepare the MicroSD card to you can boot from it.
  3. Boot the board.

NOTE: For subsequent builds, you only have to re-write the MicroSD card with a new image.

Updating the Board's Firmware

Follow these steps to update the firmware:

  1. Update the Sample Loader and MiniMonitor:

You only need to make these updates one time per device.

Follow the procedure found on the eLinux.org wiki to update to at least version 3.02, which is mandatory to run the AGL image (R-car loader update).

  1. Update the Firmware Stack:

You only need to update the firmware stack if you are using the Eel or later (5.0) version of AGL software.

M3 and H3 Renesas board are AArch64 platforms. As such, they have a firmware stack that is divided across: ARM Trusted Firmware, OP-Tee and U-Boot.

If you are using the Eel (5.0) version or later of the AGL software, you must update the firmware using the [h3ulcb]R-car h3ulcb firmware update or [m3ulcb]R-car m3ulcb firmware update links from the Embedded Linux Wiki (i.e. elinux.org).

The table in the wiki lists the files you need to flash the firmware. You can find these files in the following directory:

$AGL_TOP/build/tmp/deploy/images/$MACHINE

NOTE: The Salvator-X firmware update process is not documented on eLinux.

Preparing the MicroSD Card

Plug the MicroSD card into your Build Host. After plugging in the device, use the `dmesg` command as follows to discover the device name: 
    
$ dmesg | tail -4
[ 1971.462160] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 1971.462277] sd 6:0:0:0: [sdc] No Caching mode page found
[ 1971.462278] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1971.463870]  sdc: sdc1 sdc2

In the previous example, the MicroSD card is attached to the device /dev/sdc.

You can also use the `lsblk` command to show all your devices. Here is an example that shows the MicroSD card as `/dev/sdc`: 
    
$ lsblk
  NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
  sda      8:0    0 167,7G  0 disk
  ├─sda1   8:1    0   512M  0 part /boot/efi
  ├─sda2   8:2    0 159,3G  0 part /
  └─sda3   8:3    0   7,9G  0 part [SWAP]
  sdb      8:16   0 931,5G  0 disk
  └─sdb1   8:17   0 931,5G  0 part /media/storage
  sdc      8:32   1  14,9G  0 disk
  ├─sdc1   8:33   1    40M  0 part
  └─sdc2   8:34   1   788M  0 part

IMPORTANT NOTE: Before re-writing any device on your Build Host, you need to be sure you are actually writing to the removable MicroSD card and not some other device. Each computer is different and removable devices can change from time to time. Consequently, you should repeat the previous operation with the MicroSD card to confirm the device name every time you write to the card.

To summarize this example so far, we have the following:

Now that you have identified the device you are going to be writing the image on, you can use the bmaptool to copy the image to the MicroSD card.

Your desktop system might offer a choice to mount the MicroSD automatically in some directory. For this example, assume that the MicroSD card mount directory is stored in the $SDCARD variable.

Following are example commands that write the image to the MicroSD card:

cd $AGL_TOP/build/tmp/deploy/images/$MACHINE
bmaptool copy ./agl-demo-platform-$MACHINE.wic.xz <boot_device_name>

Alternatively, you can leave the image in an uncompressed state and write it to the MicroSD card:

  sudo umount <boot_device_name>
  xzcat ./agl-demo-platform-$MACHINE.wic.xz | sudo dd of=<boot_device_name> bs=4M
  sync

Booting the Board

Follow these steps to boot the board:

  1. Use the board's power switch to turn off the board.

  2. Insert the MicroSD card into the board.

  3. Verify that you have plugged in the following:

  4. An external monitor into the board's HDMI port

  5. An input device (e.g. keyboard, mouse, touchscreen, and so forth) into the board's USB ports.

  6. Use the board's power switch to turn on the board.

After a few seconds, you will see the AGL splash screen on the display and you will be able to log in at the console's terminal or using the graphic screen.

8. Setting Up the Serial Console

Setting up the Serial Console involves the following:

Installing a Serial Client on Your Build Host

You need to install a serial client on your build host. Some examples are GNU Screen, picocom, and Minicom.

Of these three, "picocom" has less dependencies and is therefore considered the "lightest" solution.

Connecting Your Build Host to Your Renesas Board's Serial Port

You need to physically connect your build host to the Renesas board using a USB cable from the host to the serial CP2102 USP port (i.e. Micro USB-A port) on the Renesas board.

Once you connect the board, determine the device created for the serial link. Use the ``dmesg`` command on your build host. Here is an example: 
    
dmesg | tail 9
[2097783.287091] usb 2-1.5.3: new full-speed USB device number 24 using ehci-pci
[2097783.385857] usb 2-1.5.3: New USB device found, idVendor=0403, idProduct=6001
[2097783.385862] usb 2-1.5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[2097783.385864] usb 2-1.5.3: Product: FT232R USB UART
[2097783.385866] usb 2-1.5.3: Manufacturer: FTDI
[2097783.385867] usb 2-1.5.3: SerialNumber: AK04WWCE
[2097783.388288] ftdi_sio 2-1.5.3:1.0: FTDI USB Serial Device converter detected
[2097783.388330] usb 2-1.5.3: Detected FT232RL
[2097783.388658] usb 2-1.5.3: FTDI USB Serial Device converter now attached to ttyUSB0

The device created is usually "/dev/ttyUSB0". However, the number might vary depending on other USB serial ports connected to the host.

To use the link, you need to launch the client. Here are three commands, which vary based on the serial client, that show how to launch the client:

$ picocom -b 115200 /dev/ttyUSB0

or

$ minicom -b 115200 -D /dev/ttyUSB0

or

$ screen /dev/ttyUSB0 115200

Powering on the Board to Get a Shell at the Console

Both the Pro and Premier kits (e.g. m3ulcb and h3ulcb) have nine switches (SW1 through SW9). To power on the board, "short-press" SW8, which is the power switch.

Following, is console output for the power on process for each kit:

h3ulcb: 
    

NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.7
NOTICE:  BL2: PRR is R-Car H3 ES1.1
NOTICE:  BL2: LCM state is CM
NOTICE:  BL2: DDR1600(rev.0.15)
NOTICE:  BL2: DRAM Split is 4ch
NOTICE:  BL2: QoS is Gfx Oriented(rev.0.30)
NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x52
NOTICE:  BL2: Lossy Decomp areas
NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
NOTICE:  BL2: v1.1(release):41099f4
NOTICE:  BL2: Built : 19:20:52, Jun  9 2016
NOTICE:  BL2: Normal boot
NOTICE:  BL2: dst=0xe63150c8 src=0x8180000 len=36(0x24)
NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=3072(0xc00)
NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
NOTICE:  BL2: dst=0x49000000 src=0x8640000 len=1048576(0x100000)


U-Boot 2015.04 (Jun 09 2016 - 19:21:52)

CPU: Renesas Electronics R8A7795 rev 1.1
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
=>
m3ulcb: 
    
NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14
NOTICE:  BL2: PRR is R-Car M3 Ver1.0
NOTICE:  BL2: Board is Starter Kit Rev1.0
NOTICE:  BL2: Boot device is HyperFlash(80MHz)
NOTICE:  BL2: LCM state is CM
NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x52
NOTICE:  BL2: DDR1600(rev.0.22)NOTICE:  [COLD_BOOT]NOTICE:  ..0
NOTICE:  BL2: DRAM Split is 2ch
NOTICE:  BL2: QoS is default setting(rev.0.17)
NOTICE:  BL2: Lossy Decomp areas
NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
NOTICE:  BL2: v1.3(release):4eef9a2
NOTICE:  BL2: Built : 00:25:19, Aug 25 2017
NOTICE:  BL2: Normal boot
NOTICE:  BL2: dst=0xe631e188 src=0x8180000 len=512(0x200)
NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)


U-Boot 2015.04-dirty (Aug 25 2017 - 10:55:49)

CPU: Renesas Electronics R8A7796 rev 1.0
Board: M3ULCB
I2C:   ready
DRAM:  1.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot:  0
=>

9. Setting-up U-boot

Configuring U-Boot Parameters

Follow these steps to configure the board to use the MicroSD card as the boot device and also to set the screen resolution:

  1. As the board is powering up, press any key to stop the autoboot process. You need to press a key quickly as you have just a few seconds in which to press a key.

  2. Once the autoboot process is interrupted, use the board's serial console to enter printenv to check if you have correct parameters for booting your board:

    Here is an example using the h3ulcb board: 
            
    

    => printenv
baudrate=115200
bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
bootdelay=3
fdt_high=0xffffffffffffffff
initrd_high=0xffffffffffffffff
load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb.dtb
load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
stderr=serial
stdin=serial
stdout=serial
ver=U-Boot 2015.04 (Jun 09 2016 - 19:21:52)
    

    Environment size: 648/131068 bytes
    Here is a second example using the m3ulcb board: 
        
=> printenv
baudrate=115200
bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
bootdelay=3
fdt_high=0xffffffffffffffff
filesize=cdeb
initrd_high=0xffffffffffffffff
load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb.dtb
load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
stderr=serial
stdin=serial
stdout=serial
ver=U-Boot 2015.04 (Nov 30 2016 - 18:25:18)
    

    Environment size: 557/131068 bytes

  3. To boot your board using the MicroSD card, be sure your environment is set up as follows:

    setenv bootargs console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2
setenv bootcmd run load_ker\; run load_dtb\; booti 0x48080000 - 0x48000000
setenv load_ker ext4load mmc 0:1 0x48080000 /boot/Image

  4. Loading dtb :

    NOTE : Refer here for more information.

    Make sure your load_dtb is set as follows :

    • H3SK v2.0(DDR 4GB) : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb.dtb

    • H3SK v2.0(DDR 8GB)/v3.0(DDR 8GB) : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb-4x2g.dtb

    • M3SK v1.0 : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb.dtb

    • M3SK v3.0 : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb-2x4g.dtb

    • H3SK with a Kingfisher board : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb-kf.dtb

    • M3SK with a Kingfisher board : $ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb-kf.dtb

  5. Save the boot environment:

    saveenv

  6. Boot the board: 

      run bootcmd

10. Troubleshooting

Logging Into the Console

Once the board boots, you should see the Wayland display on the external monitor. A login prompt should appear as follows depending on your board:

h3ulcb:

Automotive Grade Linux ${AGL_VERSION} h3ulcb ttySC0

h3ulcb login: root

m3ulcb:

Automotive Grade Linux ${AGL_VERSION} m3ulcb ttySC0

m3ulcb login: root

At the prompt, login by using root as the login. The password is "empty" so you should not be prompted for the password.

Determining the Board's IP Address

If your board is connected to a local network using Ethernet and if a DHCP server is able to distribute IP addresses, you can determine the board's IP address and log in using ssh.

Here is an example for the m3ulcb board: 
    
  m3ulcb login: root
  Last login: Tue Dec  6 09:55:15 UTC 2016 on tty2
  root@m3ulcb:~# ip -4 a
  1: lo:  mtu 65536 qdisc noqueue state UNKNOWN group default
      inet 127.0.0.1/8 scope host lo
        valid_lft forever preferred_lft forever
  3: eth0:  mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
      inet 10.0.0.27/24 brd 10.0.0.255 scope global eth0
        valid_lft forever preferred_lft forever
  root@m3ulcb:~#
In the previous example, IP address is 10.0.0.27. Once you know the address, you can use `ssh` to login. Following is an example that shows logging into SSH and then displaying the contents of the `/etc/os-release` file: 
    
  $ ssh root@10.0.0.27
  Last login: Tue Dec  6 10:01:11 2016 from 10.0.0.13
  root@m3ulcb:~# cat /etc/os-release
  ID="poky-agl"
  NAME="Automotive Grade Linux"
  VERSION="3.0.0+snapshot-20161202 (chinook)"
  VERSION_ID="3.0.0-snapshot-20161202"
  PRETTY_NAME="Automotive Grade Linux 3.0.0+snapshot-20161202 (chinook)"

11. Supplementary Information

Refer to the following for more information from eLinux website.

The meta-rcar-gen3 layer of meta-renesas is supported Graphic GLES(GSX) libraries, proprietary library of multimedia, and ICCOM software.

  1. Build with Renesas multimedia libraries

Multimedia portions depend on GLES portions.

**Additional configuration in OMX module** 
    
    " h263dec_lib"       - for OMX Media Component H263 Decoder Library
    " h264dec_lib"       - for OMX Media Component H264 Decoder Library
    " h264enc_lib"       - for OMX Media Component H.264 Encoder Library
    " h265dec_lib"       - for OMX Media Component H265 Decoder Library
    " mpeg2dec_lib"      - for OMX Media Component MPEG2 Decoder Library
    " mpeg4dec_lib"      - for OMX Media Component MPEG4 Decoder Library
    " vc1dec_lib"        - for OMX Media Component VC-1 Decoder Library
    " divxdec_lib"       - for OMX Media Component DivX Decoder Library
    " rvdec_lib"         - for OMX Media Component RealVideo Decoder Library
    " alacdec_lib"       - for OMX Media Component ALAC Decoder Library
    " flacdec_lib"       - for OMX Media Component FLAC Decoder Library
    " aaclcdec_lib"      - for OMX Media Component AAC-LC Decoder Library
    " aaclcdec_mdw"      - for AAC-LC 2ch Decoder Middleware for Linux
    " aacpv2dec_lib"     - for OMX Media Component aacPlus V2 Decoder Library
    " aacpv2dec_mdw"     - for aacPlus V2 Decoder Middleware for Linux
    " mp3dec_lib"        - for OMX Media Component MP3 Decoder Library
    " mp3dec_mdw"        - for MP3 Decoder Middleware for Linux
    " wmadec_lib"        - for OMX Media Component WMA Standard Decoder Library
    " wmadec_mdw"        - for WMA Standard Decoder Middleware for Linux
    " dddec_lib"         - for OMX Media Component Dolby(R) Digital Decoder Library
    " dddec_mdw"         - for Dolby(R) Digital Decoder Middleware for Linux
    " aaclcenc_lib"      - for OMX Media Component AAC-LC Encoder Library
    " vp8dec_lib"        - for OMX Media Component VP8 Decoder Library for Linux
    " vp8enc_lib"        - for OMX Media Component VP8 Encoder Library for Linux
    " vp9dec_lib"        - for OMX Media Component VP9 Decoder Library for Linux
    " aaclcenc_mdw"      - for AAC-LC Encoder Middleware for Linux
    " cmsbcm"            - for CMS Basic Color Management Middleware for Linux
    " cmsblc"            - for CMS CMM3 Backlight Control Middleware for Linux
    " cmsdgc"            - for CMS VSP2 Dynamic Gamma Correction Middleware for Linux
    " dtv"               - for ISDB-T DTV Software Package for Linux
    " dvd"               - for DVD Core-Middleware for Linux
    " adsp"              - for ADSP driver, ADSP interface and ADSP framework for Linux
    " avb"               - for AVB Software Package for Linux
    
  
Ex:

```sh
DISTRO_FEATURES_append = " h264dec_lib h265dec_lib mpeg2dec_lib aaclcdec_lib aaclcdec_mdw"
```

Must ensure that Multimedia features have been enabled. (Please refer to III/A to enable Multimedia.)